﻿NU1XA Owner's Manual

Connecting to Other Devices

Connectors
You can connect other devices to this instrument’s connectors. For information about location of these connectors, refer to “Panel Controls and Terminals” on page 12. You can also connect this instrument to a smart device such as a smartphone via Bluetooth (page 67).

NOTE
Before using the Bluetooth function, be sure to read “About Bluetooth” on page 67.

(Figure)
Terminal panel (at the bottom left of the keyboard)
Headphone jacks (page 17)
Terminal panel (at the bottom right of the keyboard)

CAUTION
Before connecting the instrument to other electronic components, turn off the power of all the components. Also, before turning any components on or off, make sure to set all volume levels to minimum (0). Otherwise, damage to the components, electrical shock, or even permanent hearing loss may occur.

1	[USB TO DEVICE] terminal
You can connect a USB flash drive to this terminal, or use a USB wireless LAN adaptor UD-WL01 (sold separately) to connect with a smart device such as a smartphone. For details, refer to “Connecting to a Computer” (page 65) or “Using the Smart Device App “Smart Pianist”” (page 70). Before using the [USB TO DEVICE] terminal, be sure to read “Precautions when using the [USB TO DEVICE] terminal” on page 64.

NOTE
There are two different types of USB terminals on the instrument: [USB TO DEVICE] and USB [TO HOST]. Take care not to confuse the two terminals and the corresponding cable connectors. Be careful to connect the proper plug in the proper direction.

2	USB [TO HOST] terminal
This terminal allows connection to a computer or a smart device, such as smartphone or tablet. For details, refer to “Connecting to a Computer” (page 65) or “Connecting to a Smart Device” (page 67).

3	MIDI [IN] [OUT] terminals
These terminals are used to connect external MIDI devices, such as a synthesizer or a sequencer. For details, refer to “Connecting External MIDI Devices (MIDI Terminals)” on page 65.

4	[AUX IN] jack
This jack is used to connect an audio player, such as a smartphone or portable audio player. For details, refer to “Connecting to an Audio Player ([AUX IN] jack)” on page 63.

5	AUX OUT [L/L+R] [R] jacks
These jacks are used to connect to external powered speaker systems (page 63).


Connecting to an Audio Player ([AUX IN] jack)
You can connect the headphone jack of an audio player, such as a smartphone or portable audio player, to the instrument’s [AUX IN] jack. Audio playback on the connected device is output from the built-in speakers of this instrument.

NOTE
• The instrument’s [MASTER VOLUME] setting affects the input signal from the [AUX IN] jack.
• Use audio cables and adaptor plugs having no (zero) resistance.

(Figure)
Portable audio player
Headphone jack
Phone plug (stereo mini)
Audio cable
Audio signal
Instrument
[AUX IN]
Phone plug (stereo mini)

NOTICE
To avoid damage to the devices, first turn on the power to the external device, and then to the instrument. When turning off the power, first turn off the power to the instrument, and then to the external device.


Using an External Speaker System for Playback (AUX OUT [L/L+R]/[R] jacks)
These jacks let you connect the instrument to external powered speaker systems, for playing in larger venues at higher volumes.
(Figure)
NU1XA
AUX OUT [L/L+R]/[R]
Phone plug (standard)
Audio cable
Audio signal
Powered speaker
AUX IN
Phone plug (standard)

NOTE
• Use only the [L/L+R] jack for connection with a monaural device.
• Use audio cables and adaptor plugs having no (zero) resistance.
• When you are monitoring the sound output via the AUX OUT jacks from headphones connected to the instrument, we recommend that you set the Binaural Sampling and Stereophonic Optimizer functions to off. For details, refer to page 18.

NOTICE
• To avoid possible damage, first turn on the power to the instrument, then to the external device. When turning off the power, first turn off the power to the external device, then to the instrument. Since this instrument’s power may automatically be turned off due to the Auto Power Off function (page 16), turn off the power to the external device, or disable Auto Power Off when you do not intend to operate the instrument.
• Do not route the output from the AUX OUT jacks to the [AUX IN] jack. If you make this connection, the signal input at the [AUX IN] jack is output from the AUX OUT jacks. These connections could result in a feedback loop that will make normal performance impossible, and may even damage the equipment.

The output volume from the AUX OUT jacks can be adjusted by the [MASTER VOLUME] control on the instrument. If you want to mute the speaker of the instrument while the external speakers are connected to the AUX OUT jacks, set the “Speaker” parameter to off via the “System” menu: “Utility” > “Speaker” (page 88).


Connecting USB Devices ([USB TO DEVICE] Terminal)
You can connect a USB flash drive or a USB wireless LAN adaptor UD-WL01 (sold separately) to the [USB TO DEVICE] terminal. You can save data you’ve recorded on the instrument to the USB flash drive (pages 46, 57), or you can connect the instrument to a smart device such as a smartphone via wireless LAN (page 71).

Precautions when using the [USB TO DEVICE] terminal
This instrument features a built-in [USB TO DEVICE] terminal. When connecting a USB device to the terminal, be sure to handle the USB device with care.
Follow the important precautions below.

NOTE
For more information about the handling of USB devices, refer to the owner’s manual of the USB device.

Compatible USB devices
• USB flash drive
• USB wireless LAN adaptor UD-WL01 (sold separately; may not be available in some areas)

Other USB devices such as a computer keyboard or mouse cannot be used.
The instrument does not necessarily support all commercially available USB devices. Yamaha cannot guarantee operation of USB devices that you purchase.
Before purchasing a USB device for use with this instrument, please visit the following web page:
https://download.yamaha.com/

Although USB devices 2.0 to 3.0 can be used on this instrument, the amount of time for saving to or loading from the USB device may differ depending on the type of data or the status of the instrument.
USB 1.1 devices cannot be used on this instrument.

NOTICE
The rating of the [USB TO DEVICE] terminal is a maximum of 5 V/500 mA. Do not connect USB devices having a rating above this, since this can cause damage to the instrument itself.

Connecting a USB device 
(Figure)
When connecting a USB device to the [USB TO DEVICE] terminal, make sure that the connector on the device is appropriate and that it is connected in the proper direction.

NOTICE
• Avoid connecting or disconnecting the USB device during playback/recording and file management operations (such as Save, Copy, Delete and Format), or when accessing the USB device. Failure to observe this may result in “freezing” of the operation of the instrument or corruption of the USB device and the data.
• When connecting then disconnecting the USB device (and vice versa), make sure to wait a few seconds between the two operations.
• Do not use extension or adaptor cables to connect USB devices.

Using USB Flash Drives
By connecting the instrument to a USB flash drive, you can save data you’ve created to the connected device, as well as read data from the connected USB flash drive.

Number of USB flash drives that can be used
Only one USB flash drive can be connected to the [USB TO DEVICE] terminal. 

Formatting a USB flash drive
You should format the USB flash drive only with this instrument (page 88). A USB flash drive formatted on another device may not operate properly.

NOTICE
The format operation overwrites any previously existing data. Make sure that the USB flash drive you are formatting does not contain important data.

To protect your data (write-protect)
To prevent important data from being inadvertently erased, apply the write-protect provided with each USB flash drive. If you are saving data to the USB flash drive, make sure to disable write-protect.

Turning off the instrument
When turning off the instrument, make sure that the instrument is NOT accessing the USB flash drive by playback/recording or file management (such as during Save, Copy, Delete and Format operations).
Failure to do so may corrupt the USB flash drive and the data.


Connecting External MIDI Devices (MIDI Terminals)
The sophisticated MIDI functions give you powerful tools to expand your music performance and creation possibilities. Use the MIDI terminals and standard MIDI cables to connect external MIDI devices (keyboard, sequencer, etc.)

MIDI [IN]: Receives MIDI messages from another MIDI device.
MIDI [OUT]: Transmits MIDI messages generated on this instrument to another MIDI device.

(Figure)
NU1XA
External MIDI device
MIDI OUT, MIDI IN
MIDI transmit
MIDI OUT, MIDI IN
MIDI receive

NOTE
• For details about MIDI, refer to “MIDI Basics” downloadable from the Yamaha website (page 9).
• Since MIDI data that can be transmitted or received varies depending on the type of MIDI device, check the MIDI Data Format to find out what MIDI data and commands your devices can transmit or receive. The MIDI Data Format is contained in the “MIDI Reference” downloadable from the Yamaha website (page 9).
•  When transmitting MIDI data from this instrument to an external MIDI device, unexpected sounds may occur because of data related to the Grand Expression Modeling.

CAUTION
Before connecting the instrument to other MIDI devices, turn off the power of all the components.


Connecting to a Computer
By connecting a computer to the USB [TO HOST] terminal via a USB cable, you can transfer MIDI data or Audio data between the instrument and the computer. For details on using a computer with this instrument, refer to the “Computer-related Operations” on the website (page 9).
(Figure)
NU1XA
USB [TO HOST]
USB cable
Computer
USB terminal

NOTE
• When using a USB cable to connect the instrument to your computer, make the connection directly without passing through a USB hub.
• For information on setting up your sequence software, refer to the owner’s manual of the relevant software.
• The instrument will begin transmission a short time after the computer or smart device is connected.
• Unexpected sounds may occur if you edit MIDI data related to the Grand Expression Modeling on a computer.

NOTICE
• Use an AB type USB cable of less than 3 meters. USB 3.0 cables cannot be used.
• If you are using a DAW (digital audio workstation) application with this instrument, set the Audio Loopback function to off (see below). Otherwise, a loud sound may occur, depending on the settings of the computer or the application software.


Transmitting/Receiving Audio Data (USB Audio Interface function)
By connecting a computer or a smart device to the USB [TO HOST] terminal via a USB cable, digital audio data can be transmitted/received. This USB Audio Interface function provides the following advantages:

NOTE
• When transmitting or receiving audio signals by using a computer running Windows, the Yamaha Steinberg USB Driver should be installed to the computer. For details, refer to the “Computer-related Operations” on the website.
• The volume of the audio sound input can be adjusted from a computer or smart device.

Playing back audio data with high sound quality
This gives you direct, clear sound in which the sound quality has less noise and deterioration than that from the [AUX IN] jack.

Recording performance on the instrument as audio data by using a recording software or a music production software
The recorded audio data can be played back on the computer or smart device.

For instructions on connecting to a computer, refer to “Computer-related Operations” on the website (page 9). To connect a smart device by using the smart device app “Smart Pianist,” refer to page 70.


Audio Loopback On/Off
This allows you to set whether audio sound input from the connected computer or smart device is output to a computer or a smart device or not along with the performance played on the instrument. To output the audio input sound, set the Audio Loopback to “On.”
For example, if you want to record the audio input sound as well as the sound played on the instrument by using the computer or the smart device, set this to “On.” If you intend to record only the sound played on the instrument by using the computer or the smart device, set this to “Off.” For details on the settings, refer to “Audio Loopback” on page 88.

NOTE
• The Audio Loopback function also affects the audio input sound when using the Bluetooth Audio function (page 68) or the wireless LAN connection (page 71).
• The playback sound of an Audio Song (page 36) is also output to a computer or smart device when this is set to “On,” while the sound is not output when this is set to “Off.”
• With Audio Recording (page 52), the audio input sound from the connected computer or smart device is recorded when this is set to “On,” while the sound is not recorded when this is set to “Off.”


Connecting to a Smart Device
Connecting a smart device such as a smartphone or tablet allows you to enjoy the features shown below. You can listen to audio playback from a smart device on your instrument’s speakers, or use a compatible smart device app to make playing this instrument easier and more fun. The method of connection varies depending on your intended use.

NOTICE
Do not place your smart device in an unstable position. Doing so may cause the device to fall and result in damage.

Transmitting/receiving audio data (USB Audio Interface function)
Connect the device to this instrument’s USB [TO HOST] terminal via a USB cable. For details, refer to page 66.

Listening to audio played back on a smart device through the speakers of this instrument (Bluetooth* Audio function)
Connect the device to this instrument via Bluetooth. For details, refer to page 68.

Using the Smart Device App “Smart Pianist”
Connect the device to this instrument via Bluetooth* or other methods. For details, refer to page 70.


About Bluetooth

Bluetooth capability
NU1XA is equipped with Bluetooth functionality; however, even these models may not support Bluetooth, depending on the country in which you purchased the product. If the Bluetooth logo is shown or printed on the control panel, this means that the product is equipped with Bluetooth functionality. 
(Figure)
Bluetooth logo

Bluetooth is a technology for wireless communication between devices within an area of about 10 meters (33 ft.) employing the 2.4 GHz frequency band.

Handling Bluetooth communications
• The 2.4 GHz band used by Bluetooth compatible devices is a radio band shared by many types of equipment. While Bluetooth compatible devices use a technology minimizing the influence of other components using the same radio band, such influence may reduce the speed or distance of communications and in some cases interrupt communications.
• The speed of signal transfer and the distance at which communication is possible differs according to the distance between the communicating devices, the presence of obstacles, radio wave conditions and the type of equipment.
• Yamaha does not guarantee all wireless connections between this unit and devices compatible with Bluetooth function.


Listening to Audio Data from a Smart Device through this Instrument (Bluetooth Audio Function)
Before using the Bluetooth function, be sure to read “About Bluetooth” on page 67.

You can input the sound of the audio data saved in a Bluetooth-equipped device, such as a smart phone or digital audio player, to this instrument and listen to it through the built-in speaker of the instrument.
To use this function, make sure that Bluetooth is set to “On” (page 69) on the instrument (default setting: On). 
(Figure)
[Menu] button
[Exit] button
[Bluetooth] button

NOTE
• In this manual, a smart device is used as an example of a Bluetooth-equipped device which allows Bluetooth transmission of contained audio data to the instrument, via wireless  communication. For proper operation, the device must be compatible with A2DP (Advanced Audio Distribution Profile). The Bluetooth Audio function is explained here by using a smart device as an example of such Bluetooth-equipped devices.
• Refer to page 70 for transmitting/receiving the MIDI data between the instrument and the smart device via Bluetooth.
• Bluetooth headphones or speakers cannot be paired.

Pairing
“Pairing” means to register Bluetooth-equipped smart devices on this instrument, and establish the mutual recognition for wireless communication between the two.

NOTE
• Only one smart device can be connected to this instrument at a time (although up to 8 smart devices can be paired to this instrument). When pairing with the 9th smart device has succeeded, pairing data for the device with the oldest connection date will be deleted.
• Make sure to complete the settings on the smart device within 5 minutes.
• If you are required to enter a passkey, enter the numerals “0000.”

NOTE
You can adjust the volume of the sound input via Bluetooth by the [MASTER VOLUME] control. To adjust the volume balance between your keyboard performance and the input sound via Bluetooth, adjust the volume on the smart device.

1	Hold down the [Bluetooth] button for 3 seconds.
The pop-up window will appear which indicates that the instrument is standing by for pairing.
(Figure)

To cancel the pairing, press the [Exit] button

2	On the smart device, set the Bluetooth function to on and select “NU1XA AUDIO” from the connection list.
For details, refer to the smart device owner’s manual.
After pairing is completed, the connection status will be shown in the display.
(Figure)
Can receive audio data

3	Play back audio data on the smart device to confirm that the built-in speakers of the instrument can output the audio sound.
When you turn on the instrument the next time, the last-connected smart device will be connected to this instrument automatically, if the Bluetooth function of the smart device and the instrument is set to on. If it is not connected automatically, select the model name of the instrument from the connection list on the smart device.


Switching the Bluetooth Function On/Off
Before using the Bluetooth function, be sure to read “About Bluetooth” on page 67.

By default, the Bluetooth function will be on right after turning the instrument’s power on, however you can set the function to off.

1	Press the [Menu] button repeatedly to call up the “System” menu display, then select the highlighted item in each display as illustrated below.
(Figure)
“System” menu display
1-1.	Confirm that “Bluetooth” is selected.
1-2.	Press the [Cursor right] button to call up the next display.
“Bluetooth” display
1-3.	Confirm that “Bluetooth” is selected.

2	Press the [Cursor right] button to switch on/off.
To exit from the “System” menu display, press the [Exit] button.


Using the Smart Device App “Smart Pianist”
By connecting a smart device such as a smartphone or tablet and using the Smart Pianist app, you can view the score of the preset Songs on the smart device, record your performance to the smart device, and perform other convenient operations. The intuitive visual interface helps you to confirm the current settings of the instrument.
For details on the app and compatible devices, access the website below and visit the “Smart Pianist” page. 

(QR code)
https://www.yamaha.com/2/apps/

NOTE
When using the “Smart Pianist” app, you cannot use any buttons on the instrument other than the [Exit] button. Control the instrument by using “Smart Pianist.” 
Pressing the [Exit] button on the instrument disconnects the instrument from the “Smart Pianist” app, and enables you to control the instrument by using its buttons.

NOTICE
Activating the “Smart Pianist” app while the instrument is connected to the smart device overwrites the settings on the instrument by that of “Smart Pianist.” Save your important setup data as a backup file to a USB flash drive (page 92).

You can connect your smart device to this instrument via Bluetooth, USB cables or Wi-Fi.
The “Connection Wizard” of Smart Pianist guides you in properly connecting the smart device to the instrument properly. After installing the Smart Pianist app on your smart device, tap [Menu] located at the upper left on the Smart Pianist screen to open the menu, and then tap “Instrument” followed by “Start Connection Wizard.”
For details on the connection methods as well as how to use the app, refer to the “Smart Pianist User Guide” on the following website.

(QR code)
https://manual.yamaha.com/mi/app/smartpianist/

This section explains the operations particular to this instrument. For the necessary settings on this instrument, follow the instructions below.


Connecting via Bluetooth
Before using the Bluetooth function, be sure to read “About Bluetooth” on page 67. Information on the availability of Bluetooth functionality is included or not can also be found on that page.

Two different types of Bluetooth connection are available: “Bluetooth MIDI” and “Bluetooth Audio.”
You need to connect by Bluetooth MIDI to link and use Smart Pianist with the instrument. Bluetooth MIDI connection allows you to transmit and receive MIDI data between the instrument and the smart device. When connecting, select “NU1XA MIDI” on Smart Pianist as the device for connection.
If you connect by Bluetooth Audio as well, the audio data in the smart device can be played through Smart Pianist. Note that you cannot record your keyboard performance as audio format on Smart Pianist. For instructions on setting the Bluetooth Audio function, refer to page 68.
When the Bluetooth connection is made successfully, the connection status is shown on the Voice display.
(Figure)
Voice display
Can transmit and receive MIDI data
Can transmit and receive MIDI data, and receive audio data

NOTE
If the Bluetooth function of this instrument is set to Off (default setting: On), the Bluetooth connection cannot be made. For information on the setting, refer to page 69.


Connecting via USB cables
Connect the smart device to the USB [TO HOST] terminal via USB cables. With this method, audio data as well as MIDI data can be transmitted or received between the instrument and the smart device. This allows you to play the audio data in the smart device through Smart Pianist, and also allows you to record your keyboard performance as audio format on Smart Pianist.


Connecting via Wi-Fi (by using the USB wireless LAN adaptor*)
*The USB wireless LAN adaptor UD-WL01 (sold separately) may not be available depending on your area.

Connect the smart device via Wi-Fi by connecting the USB wireless LAN adaptor UD-WL01 (sold separately) to the [USB TO DEVICE] terminal. With this method, audio data as well as MIDI data can be transmitted or received between the instrument and the smart device. This allows you to play the audio data in the smart device through Smart Pianist, and also allows you to record your keyboard performance as audio format on Smart Pianist.
Make either of the settings below, and then follow the “Connection Wizard” on Smart Pianist.

Connecting by the Infrastructure mode
The Infrastructure mode uses an access point for data communication between a USB wireless LAN adaptor and a network. You can use this mode when you connect to another network while a smart device is connected to the instrument.
• Displaying the Wireless LAN networks and connecting to a network (page 72)
• Automatic Setup by WPS (page 73)
• Manual Setup (page 73)

Connecting by the Accesspoint mode (page 74)
The Accesspoint mode allows you to directly connect the USB wireless LAN adaptor and a smart device, without the need for using an access point. You can use this mode when no access point is available for connection to the instrument, or when it is unnecessary to connect to another network while a smart device is connected to the instrument.
When connected by this mode, Internet access is disabled on your smart device, and some functions of Smart Pianist cannot be used.

NOTICE
Do not connect this product to public Wi-Fi and/or Internet directly. Only connect this product to the Internet through a router with strong password protections. Consult your router manufacturer for information on security best practices.


Displaying the Wireless LAN networks and connecting to a network
Make sure to connect the USB wireless LAN adaptor (sold separately) to the [USB TO DEVICE] terminal, otherwise the displays for setup below will not be shown.
(Figure)
[Menu] button

NOTE
If the menus shown in the Wireless LAN display, are different from those shown here, the instrument is in the Accesspoint mode. Set the Wireless LAN Mode parameter to “Infrastructure Mode” by following the step 1 on page 74.

1	Press the [Menu] button repeatedly to call up the “System” menu display, and then select the highlighted item in each display as illustrated below. 
(Figure)
“System” menu display
1-1.	Use the [Cursor up]/[Cursor down] buttons to select “Utility.”
1-2.	Press the [Cursor right] button to call up the next display.
“Utility” display
1-3.	Use the [Cursor up]/[Cursor down] buttons to select “Wireless LAN.”
1-4.	Press the [Cursor right] button to call up the next display.
“Wireless LAN” display
1-5.	Use the [Cursor up]/[Cursor down] buttons to select “Select Network.”

2	Press the [Cursor right] button to call up the network list.
For a network with a lock icon, you need to enter the proper password.
(Figure)

NOTE
If no signal from the access point is received, the access point cannot be listed. Also, closed access points cannot be listed.

3	Connect the instrument to the Network.

3-1	Select the desired network, then press the [Cursor right] button.
The name of the selected network will be fully shown in the display, letting you confirm this is the network you want to use.

3-2	Press the [Cursor right] button.

For a network without a lock icon:
Connecting starts.

For a network with a lock icon:
You need to enter the proper password. For details on how to enter characters, refer to the “Renaming Song Files — Rename” on page 61. After entering the password, press the [Menu] button to finalize the setting. This operation starts connecting automatically.

When connection is done successfully, “Completed” is shown in the display, and returns to the “Select Network” display.

4	Connect the smart device to the access point.
Open the Wi-Fi settings on your smart device, and select the network containing “NU1XA” in the name field. If a password is requested, input it to connect.


Automatic Setup by WPS
Please make sure to connect the USB wireless LAN adaptor (sold separately) to the [USB TO DEVICE] terminal, otherwise the displays for setup will not be shown.

If your access point supports WPS, you can easily connect the instrument to access point by WPS, without making settings, such as password input, etc.
Press the WPS button on the USB wireless LAN adaptor more than 3 seconds, and press the WPS button on your access point within two minutes.
When connection is done successfully, “Completed” is shown in the display, and the Voice display will be shown.

Finally, connect the smart device to the access point (step 4 above).

NOTE
WPS setup is not available while the instrument is in the following modes or conditions:
• While a Song or a Demo Song is playing back or being paused temporarily, or while the instrument is in the Song Recording mode.
• When Wireless LAN mode is set to “Accesspoint Mode” in the “System” menu.


Manual Setup
Make sure to connect the USB wireless LAN adaptor (sold separately) to the [USB TO DEVICE] terminal, otherwise the displays for setup will not be shown.

1	To call up the network list, perform steps 1 – 2 in the “Displaying the Wireless LAN Networks and connecting to a Network” (page 72).
(Figure)

2	Select “Other” at the bottom of the network list, then press the [Cursor right] button.

3	Set the SSID, Security and Password to the same as the settings on the access point.
(Figure)

3-1	Select the “SSID” then press the [Cursor right] button to call up the display for SSID input, then enter the SSID.
For details on how to enter the characters, refer to “Renaming Song Files — Rename” on page 61. After entering the SSID, press the [Menu] button to finalize the setting. Operation returns to the “Other” display.

3-2	Select “Security” then press the [Cursor right] button to call up the Security list. Select the security then return to the “Other” display by pressing the [Cursor left] button.

3-3	Select “Password,” then set the password in the same way as SSID.

NOTE
The password cannot be set when you select “none” for the security setting.

4	Select “Connect >” at the bottom of the display shown in step 3, then press the [Cursor right] button to start connecting.
When connection is done successfully, “Completed” is shown in the display, and returns to the “Select Network” display.

5	Connect the smart device to the access point.
This operation is the same as step 4 on page 73.


Connecting by the Accesspoint Mode
(Figure)
[Menu] button

1	Switch the instrument to the “Accesspoint Mode.”
Press the [Menu] button repeatedly to call up the “System” menu display, then select the highlighted item in each display as illustrated below.
(Figure)
“System” menu display
1-1.	Use the [Cursor up]/[Cursor down] buttons to select “Utility.”
1-2.	Press the [Cursor right] button to call up the next display.
“Utility” display
1-3.	Use the [Cursor up]/[Cursor down] buttons to select “Wireless LAN Option.”
1-4.	Press the [Cursor right] button to call up the next display.
“Wireless LAN Option” display
1-5.	Use the [Cursor up]/[Cursor down] buttons to select “Wireless LAN Mode.”
1-6.	Press the [Cursor right] button to call up the next display.
“Wireless LAN Mode” display
1-7.	Use the [Cursor up]/[Cursor down] buttons to select “Accesspoint Mode.”

When mode change is done successfully, “Completed” is shown in the display, operation returns to the “Wireless LAN Mode” display.

2	Set SSID, Security, Password and Channel.

2-1	From the “System” menu display, select the highlighted item in each display as illustrated below.
(Figure)
“System” menu display
“Utility” display
“Wireless LAN” display

2-2	Set the SSID, Security, Password and Channel.
Select and enter each value/setting in the same way as in step 3 in “Manual Setup.” For the setting range for each item, refer to “Wireless LAN” (In the Accesspoint mode) on page 91.

3	Save the setting.
Select “Save >” at the bottom of the Wireless LAN display, then press the [Cursor right] button to start saving.
When saving is done successfully, “Completed” is shown in the display, and operation returns to the “Utility” display.

4	Connect the smart device to the instrument (as an access point).
This operation is the same as step 4 on page 73.


This is the end of the file.